AiM Sports

AiM 90 22 Pin Auxiliary Harness for MXP, MXG, MXS & MXL2 Dashes 90 This 90 harness plugs into the 22-pin connector on either the AiM MXP, MXL2, MXM, MXG, MXS dash, and AiM EVO5 Logger. Several of the advanced functions rely on this harness, which is not included with the standard kit. AiM 22 Pin Auxiliary Harness for MXP, MXG, MXS, MXL2 Dashes Details: Manufacturer: AiM Manufacturer part number: V02573020 Alternate part number: MC-249 Harness Angle: 90 The AiM 22 Pin Auxiliary Harness will provide access to the following functions: Analog sensor channels 5, 6, 7, 8 Digital wheel speed sensor inputs 2, 3, 4 Digital 12v outputs 1, 2 RS232 ECU connection The factory harness that comes with the AiM MXG, MXS, MXL2 allows only 4 inputs. If you would like more inputs then this is your harnessFor use with AiM MXS, MXP, MXL2, MXG, and EVO5 Dash/Loggers. Not compatible with older AiM MXL Pro / MXL Pro05 or AiM EVO series. AiM 22 Pin Auxiliary Harness for MXP, MXG, MXS, MXL2 Dashes Primary use: Adding analog sensors greater than 4. Your factory harness will allow up to 4 analog channels (sensors), this may be (1) Water Temperature, (2) Oil Temperature, (3) Oil Pressure and (4) Brake Pressure. Using the AiM 22 Pin Auxiliary harness you now can add four more analog channels (sensors) like (5) Steering Angle, (6) Throttle Position, (7) Gear Box Temperature, and (8) Differential Temp. Another way we see this cable used is independent shock travel (all corners) or engine oil temperature pre-cooler and oil temperature post-cooler.

AiM PDM CAN-Configurable Keypad - 12-Button PDM Buttons sold separately here This is a CAN-programmable 12-button panel compatible with AiM PDM systems (PDM08 and PDM32). This keypad comes pre-configured for use with AiM protocols and is ready to be programmed through AiM's RaceStudio software. The buttons measure 15mm size and the overall panel size is 181.5mm x 70.0mm x 16.3mm (7.14x2.75x0.64"). AiM PDM CAN-Configurable Keypad - 12-Button Details: Manufacturer: AiM Sports Manufacturer part number: KEY012 Weight: 220g (7.76oz) Connector: Deutsch 6-pin, DT04-4P Supply voltage: 12-24Vdc, Nominal 8-32Vdc Standy current: <50mA Communications BUS: RS485, CANopen J1939 Operating temperature: -40C to +70C Thermal shock: -40C to +85C Salt spray standard: ASTMB117 Chemical resistance: Dirt, Engine cleaner, Isopropyl alcohol, Multi-purpose cleaner, Muriatic acid Waterproof rating: IP67 Button Inserts Sold Separately Each button function and backlight is programmed using AiM software and can be set up as momentary, toggle, or multi-position. Once programmed install the button insert for each button. Rear connector is a motorsport-grade Deutsch 6-pin connector wired for power, ground, CAN high, CAN low, TxRx-, and TxRx+.

AiM PDM CAN-Configurable Keypad - 8-Button PDM Buttons sold separately here This is a CAN-programmable 8-button panel compatible with AiM PDM systems (PDM08 and PDM32). This keypad comes pre-configured for use with AiM protocols and is ready to be programmed through AiM's RaceStudio software. The buttons measure 15mm size and the overall panel size is 123.5mm x 70.0mm x 16.3mm (4.86" x 2.75" x 0.64"). AiM PDM CAN-Configurable Keypad - 8-Button Details: Manufacturer: AiM Sports Manufacturer part number: KEY008 Weight: 170g (6 oz) Connector: Deutsch 6-pin, DT04-4P Supply voltage: 12-24Vdc, Nominal 8-32Vdc Standy current: <50mA Communications BUS: RS485, CANopen J1939 Operating temperature: -40C to +70C Thermal shock: -40C to +85C Salt spray standard: ASTMB117 Chemical resistance: Dirt, Engine cleaner, Isopropyl alcohol, Multi-purpose cleaner, Muriatic acid Waterproof rating: IP67 Each button function and backlight is programmed using AiM software and can be set up as momentary, toggle, or multi-position. Once programmed install the button insert for each button. Rear connector is a motorsport-grade Deutsch 6-pin connector wired for power, ground, CAN high, CAN low, TxRx-, and TxRx+.

AiM Sports GPS09 Module The GPS09 module from AiM further expands the track mapping abilities of AiM data loggers and dash loggers. In addition, the GPS09 allows lap timing (even split times) without the use of trackside beacons, storing data for up to 50 tracks with up to 5 splits per track. The GPS09 can also calculate and log speed, lateral and longitudinal g-forces, and of course vehicle position.The GPS09 is the latest version, boasting a quicker 25 Hz sampling rate (up from 10 Hz) and positional accuracy to less than one foot (down from 2 meters). It also takes full advantage of Race Studio 3's integration of GPS, video, and data. Simple to install: Just connect the CAN cable to your dash and mount the magnetic-backed GPS antenna to your vehicle roof. The GPS unit willl even automatically configure itself during start-up! The GPS09 connects via a 5-pin 712 screw-in conncetor and is compatible with current-generation AiM MXL2/ MXG/MXP/MXS auto dashes, EVO4S/EVO5 data loggers, and SmartyCam HD GP 2.2. Choose a cable length to suit your installation: 1.3m (4 ft) is appropriate for most formula cars and bikes. 4m (13 ft) is long enough for sedans. SmartyCam Note: Only the SmartyCam HD GP 2.2 takes this version. SmartyCam HD, SmartyCam HD GP, and SmartyCam HD 2.1 all require the AiM GPS09B which has a 4-pin connector. MXL / EVO3 / MyChron4 Note: This version is only compatible with the latest-generation loggers; it is not backwards-compatible with the first-gen MXL, the EVO3, or the MyChron4. Solo2/Solo2DL, MXm, and MyChron5 do not use an external GPS module; all GPS functions are internal. COMPATIBILITY GPS08 (five pin): MXL/MXL2, MXG, MXP, MXS, and MXm dashes, SmartyCam GPHD Rev 2.2, EVO3, EVO4S, and EVO5 GPS08B (four pin): SmartyCam GPHD Rev 2.1, SmartyCam GP Rev 2.1 Available in either Standard or Roof-Mount versions.

Aim Sports Channel Expansion Hub This compact CAN device provides virtually endless data acquisition system expansion options. The AiM Sports Channel Expansion Hub adds up to four freely configurable analog (or two digital and two analog) channels without occupying or modifying any of the existing system channels. By using advanced CAN technology, wiring is simplified from four cables into just a single connection, thereby reducing possible and unnecessary points of failure. Using the AiM Sports Data Hub, it's possible to connect to as many Channel Expansion Hubs as needed.

AiM MyChron Expansion The AiM MyChron Expansion is an add-on for the MyChron4 or MyChron5 Kart Racing Data Logging Dash. It plugs into the CAN expansion port on your MyChron dash to expand its capabilities. The Expansion has a single CAN expansion port plus four additional sensor inputs. All four inputs can accept common karting sensors (brake/throttle pedal position, temperature, steering angle, etc.). One of the four inputs can accept a speed sensor instead. Requires an external 12-volt power source such as your kart's battery. The MyChron Expansion channel multiplier improves MyChron5 and MyChron5 2T (and also MyChron4 and MyChron4 2T) performance, thanks to four additional channels and a further CAN bus connector. Through this last connector, the systems can be connected to LCU-One Lambda controller and SmartyCam HD (and to GPS and Data key for MyChron4 systems). Thanks to its specific wirings, MyChron Expansion powers the systems and their peripherals with an external battery, avoiding internal battery consumption. All channels are easily configurable as analog through the system menu to sample data coming from: Exhaust gas valve position sensor (very important to understand at which RPM value the exhaust port opens) Wheel speed sensor: the first input on the left can be configured also as digital input No contact brake pedal position sensor No contact throttle pedal position sensor Brake pressure sensor Water temperature or cylinder head temperature (PT100 thermo-resistor only) Steering angle potentiometer (to highlight over/under steering situations) Brake pedal potentiometer Throttle pedal potentiometer MyChron Expansion is a complete, value-for-money instrument for professional kart analysis. Call us with any questions you have about the MyChron Expansion from AiM Sports!

AiM ECU Bridge with OBDII, CAN/K Line Connector Connecting to the ECU allows the AiM unit access to data collected by your ECU (RPM, road speed, coolant temperature, and throttle position are typical; many ECUs offer much more information). Works with all AiM displays with a male 5-pin CAN connector, including the MXG, MXS, MSM, MXL, MXL Pro Dash Display, G-Dash Display, and Formula Car Wheel Display. SmartyCam requires the AiM 7-pin to 5-pin CAN Cable (Part No. MC-542, included with the SmartyCam). AiM ECU Bridge with OBDII CAN/K Line Connector Details: Manufacturer: AiM Manufacturer part number: X90BGGK12MA Alternate part number: X90BRIDGE01 Alternate part number: MC-401 CAN protocol for external modules (visors or SmartyCam HD) USB port for PC communication External power 8/18 V ECU Bridge CAN/K-line P-N-P OBDII kit* The ECU Bridge also features a special port for a USB cable (included) for easy connection to your computer for setup. ECU Bridge is available With CAN/RS232 connection, for direct installation on aftermarket ECUs. ECU Bridge and RPM Bridge: these two systems are needed whenever engine data are to be visualized on a display or on a SmartyCam HD video, if no recording is required. They are compatible with G-Dash and Formula/GT steering wheels, and of course with the SmartyCam HD on-board cameras. ECU Bridge is to be used in case the Engine Control Unit transmits data in the following hardware protocols: OBDII, CAN or RS232. AiM has developed hundreds of different protocols, to make compatibility with virtually all ECUs possible, either stock and after market ECUs. ECU Bridge has to be properly configured with Race Studio 2 software to communicate with the different visors/cameras on one side and ECUs on the other side. SmartyCam Installation Dash Display/Dash Logger Installation

AiM ECU Bridge with RS232 / CAN Wiring Connecting to the ECU allows the AiM unit access to data collected by your ECU (RPM, road speed, coolant temperature, and throttle position are typical; many ECUs offer much more information). Works with these AiM displays with a male 5-pin CAN connector: MXG MXS MSM MXL & MXL Pro G-Dash Display Formula Car Wheel Display SmartyCam requires the AiM 7-pin to 5-pin CAN Cable (Part No. MC-542, included with the SmartyCam). The ECU Bridge also features a special port for a USB cable (included) for easy connection to your computer for setup. ECU Bridge is available with CAN/RS232 connection, for direct installation on aftermarket ECUs. ECU Bridge and RPM Bridge are needed whenever engine data are to be visualized on a display or on a SmartyCam HD video, if no recording is required. ECU Bridge is used when the ECU transmits data via OBDII, CAN or RS232. AiM has developed hundreds of different protocols to make compatibility with virtually any ECU possible, stock or aftermarket. ECU Bridge has to be properly configured with Race Studio 2 software to communicate with the different visors/cameras on one side and ECUs on the other side. WIRING DETAILS: CAN protocol for external modules (visors or SmartyCam HD) USB port for PC communication External power 8/18 V

AiM Memory Module  for MXG / MXS / MXL2 / EVO4S / EVO5 Swap memory cards effortlessly to keep your driver data more organized. This unit allows you to easily swap memory cards to view driver data more efficiently between stints. AiM Memory Module  for MXG / MXS / MXL2 / EVO4S / EVO5 Details: Manufacturer: Aim Manufacturer part number: X08MMD040 Manufacturer Alternate Part Number: MC-720

AiM 23 Pin Aux Harness for MXS 1.2 Strada, MXP Strada, and MXG 1.2 Strada AiM specially designed wiring and cables for the connection of all AiM electronic components to be useful and fundamental. AiM 23 Pin Aux Harness for MXS 1.2/1.3 Strada, MXP Strada, and MXG 1.2/1.3 Strada Details: Manufacturer: AIM Manufacturer part number: V02573330 AiM 23 Pin Aux Harness for MXS 1.2/1.3 Strada, MXP Strada, and MXG 1.2/1.3 Strada Compatibility: MXS 1.2/1.3 Strada MXP Strada MXG 1.2/1.3 Strada

AiM MyChron5 Kart Racing Steering Wheel The MyChron5 Kart Steering Wheel has been specifically designed for oval karts; its shape allows a perfect view of the track and your MyChron5 is placed in the best position to keep data available at a glance. The ideal complement for your newest MyChron5, light-weight and ergonomical, it allows you to put your MyChron5 in the best position: right in front of you. You can fully access the power of the MyChron5, viewing your data at a glance while maintaining optimum driving precision. Designed with a flat bottom and curved top, the AiM MyChron5 Steering Wheel is made of an anodized aluminum frame with Alcantara grips and durable Nabuk covering on the sides. The rugged and ergonomic MyChron5 Oval Steering Wheel is a balanced mix of great design, excellent feel, and top technology all at your fingertips! SAFETY IS THE PRIMARY GOAL The outer rim has been designed without edges, to avoid any problem in case of accident. Different from traditional aluminum/steel steering wheels, the MyChron5 Steering Wheel utilizes polyurethane to minimize vibration on the driver's hands. This greatly reduces driver fatigue. The MyChron5 Karting Wheel is easy to install, resistant to all weather conditions, and jet-washable without any problem. SPECS Weight: 600g (1.3 lbs.) Diameter: 340mm (13.4 in.) Chassis: Anodized aluminum Covering: Alcantara and Nabuk Leather Call us with any questions you have about the AiM MyChron5 Kart Racing Steering Wheel from Discovery Parts!

AiM OBD Harness for MX-Series 1.2 Strada Dashes From AIM Sports, discover the specialized wiring harness compatible with the AiM MXS 1.2 Strada, MXP Strada, and MXG 1.2 Strada street dashboards. Designed to seamlessly connect via a 14-pin AMP connector, this harness ensures efficient power, ground, USB, and CAN expansions. Additionally, it facilitates a direct ECU link through the OBD-II diagnostic port. Ideal for production vehicles equipped with an OBD-II port, the harness supports both CAN and K-Line communication standards. Available for individual purchase. Note: Dashboard is sold separately."

AiM Sports KA 50 psi Boost/Vacuum (Absolute Pressure) Sensor This "absolute pressure" sensor is ideal for measuring vapor (gas) pressures, from intake boost to crankcase pressure. The 50 psi pressure range is based on perfect vacuum (i.e., from 15 psi below atmospheric pressure to 35 psi above). This sensor is marked "0-50psiA" to differentiate it from the standard 0-50 psi sensor (marked "0-50psiSG"), which does not measure vacuum. KA pressure sensors are more robust than VDO-style pressure sensors, but they should still be isolated from engine heat and vibration whenever possible. It is compatible with these AiM products: MyChron5 MXL MXL 2 MXG MXS MXM EVO3 EVO4 Features 1/8" NPT male threads.

AiM Sports Pressure Sensor NOTE: Sensors typically take 3 to 5 business days to ship. Add the appropriate AiM Sports Pressure Sensor to your AiM data set-up to retrieve exactly the information you need to maximize your data acquisition and take your racing to the next level! All sensors have a 40 cm (16 inch) cable length

 AiM Reverse or Side Mirror Camera AiM reverse and/or side view camera for use with modern AiM Dash like the MXS 1.2, MXP, MXG 1.2, MXS 1.2 Strada, MXP Strada, MXG 1.2 Strada. Featuring a wide 170° horizontal field of view, we use this camera system for rear view and door side view in sealed prototype racers whene a normal side mirror will not provide ample visibility. AiM Reverse or Side Mirror Camera Details: Manufacturer: AiM Manufacturer part number: XB1ZCAMHD00 Optical format: 1/4 inch color CMOS TV system: NTSC H-FOV: 170° Pixel array: 648 (H) x 488 (V) Frame rate: 60 fps Temperature: -30/80 °C Patch cable included: No, use AiM-V02573410